Seat Tank KitsSeat CoversCalumetair - Prerotators, seat tanks and More!
Top Quality Seat Tanks-Offered Factory Direct

Sec. 45.11- Marking of products

fmi: IDENTIFICATION AND REGISTRATION MARKING

(a) Aircraft. A manufacturer of aircraft covered under Sec. 21.182 of this chapter must mark each aircraft by attaching a fireproof identification plate that--

(1) Includes the information specified in Sec. 45.13 using an approved method of fireproof marking;

(2) Must be secured in such a manner that it will not likely be defaced or removed during normal service, or lost or destroyed in an accident; and

(3) Except as provided in paragraphs (d) through (h) of this section, must be secured to the aircraft fuselage exterior so that it is legible to a person on the ground, and must be either adjacent to and aft of the rear-most entrance door or on the fuselage surface near the tail surfaces.


(b) Aircraft engines. A manufacturer of an aircraft engine produced under a type certificate or production certificate must mark each engine by attaching a fireproof identification plate. Such plate--


(1) Must include the information specified in Sec. 45.13 using an approved method of fireproof marking;

(2) Must be affixed to the engine at an accessible location; and

(3) Must be secured in such a manner that it will not likely be defaced or removed during normal service, or lost or destroyed in an accident.


(c) Propellers and propeller blades and hubs. Each person who produces a propeller, propeller blade, or propeller hub under a type certificate or production certificate must mark each product or part. Except for a fixed-pitch wooden propeller, the marking must be accomplished using an approved fireproof method. The marking must—


(1) Be placed on a non-critical surface;

(2) Contain the information specified in Sec. 45.13;

(3) Not likely be defaced or removed during normal service; and

(4) Not likely be lost or destroyed in an accident.


(d) Manned free balloons. A manufacturer of manned free balloons must mark each balloon by attaching the identification plate described in paragraph (a) of this section. The plate must be secured to the balloon envelope and must be located, if practicable, where it is legible to the operator when the balloon is inflated. In addition, the basket and heater assembly must be permanently and legibly marked with the manufacturer's name, part number (or equivalent), and serial number (or equivalent).

(e) Aircraft manufactured before March 7, 1988. The owner or operator of an aircraft manufactured before March 7, 1988 must mark the aircraft by attaching the identification plate required by paragraph (a) of this section. The plate must be secured at an accessible exterior or interior location near an entrance, if the model designation and builder's serial number are also displayed on the exterior of the aircraft fuselage. The model designation and builder's serial number must be--


(1) Legible to a person on the ground,

(2) Located either adjacent to and aft of the rear-most entrance door or on the fuselage near the tail surfaces, and

(3) Displayed in such a manner that they are not likely to be defaced or removed during normal service.


(f) For powered parachutes and weight-shift-control aircraft, the identification plate required by paragraph (a) of this section must be secured to the exterior of the aircraft fuselage so that it is legible to a person on the ground.

(g) The identification plate described in paragraph (a) of this section may be secured to the aircraft at an accessible location near an entrance for--


(1) Aircraft produced for--


(i) Operations under part 121 of this chapter,

(ii) Commuter operations (as defined in Sec. 110.2 of this chapter), or

(iii) Export.


(2) Aircraft operating under part 121 of this chapter and under an FAA-approved continuous airworthiness maintenance program; or

(3) Aircraft operating in commuter air carrier operations (as defined in Sec. 110.2 of this chapter) under an FAA-approved continuous airworthiness maintenance program.


(h) Gliders. Paragraphs (a)(3) and (e) of this section do not apply to gliders.